Tannoy CMS801 DCBM
Producator: Tannoy3% reducere pentru contactele prin clubafaceri.ro
Prezentare Tannoy CMS801 DCBM
The CMS801 DC is equipped with a low insertion loss 60W line transformer easily configurable to the following settings via front baffle mounted rotary tapping switch:
70V systems: 60W / 30W / 15W / 7.5W / OFF & low Impedance operation
100V systems: 60W / 30W / 15W / OFF & low Impedance operation
Two CMS801 DC model versions and a separate back can are available to satisfy the vast majority of installation application requirements:
CMS801 DC BM (Blind Mount) - supplied with an integral back can.
CMS801 DC PI (Pre-Install) - supplied without a back can.
CMS801 PI Back Can (Pre-wire back can) - use with the CMS801 DC PI.
The zinc plated steel back cans have an integrated, recessed termination box. The removable locking connector has screw terminals for secure wire termination and \\\\\\\"loop through\\\\\\\" facility. Strain relief is provided by a clamping mechanism for use with plenum rated cable or conduit.
SYSTEM
Frequency Response (-3dB) (1) BM Back can 47Hz - 30kHz
Frequency Range (-10dB) (1) BM Back can 40Hz - 35kHz
Frequency Range (-10dB) (1) PI Back can 41Hz - 35kHz
System Sensitivity (1W @1m) (2) 92dB (1W = 2.83V for 8 Ohms)
Nominal Coverage Angle 90 degrees conical
Coverage Angle (1kHz to 6kHz) 100 degrees
Directivity Factor (Q) 5.5 averaged 1kHz to 6kHz
Directivity Index (DI) 7.2 averaged 1kHz to 6kHz
Rated Maximum SPL Average: 112dB
Peak: 118dB
Average: 110dB (with THP60)
Power Handling (3) Average: 90W
Programme: 180W
Peak: 360W
Recommended Amplifier Power 180W @ 8 Ohms
Nominal Impedance 8 Ohms
Transformer Taps (via front rotary switch) 70V: 60W / 30W / 15W / 7.5W / OFF
& Low Impedance operation
100V: 60W / 30W / 15W / OFF
& Low Impedance operation
Crossover 2kHz - 2nd order LF, 2nd order HF
(with dynamic HF protection)
TRANSDUCERS
Low Frequency 1 x 200mm (8.00\\\") Dual Concentric constant directivity driver with multi fibre paper pulp cone
High Frequency 1 x 25mm (1.00\\\") titanium dome with neodymium magnet system
PHYSICAL
Enclosure Back Can: Zinc plated steel
Baffle: Reflex loaded UL 94V-0 rated ABS Grille: Steel, with weather resistant coating
Safety Features Safety ring located at rear of enclosure for load bearing safety bond
Clamping Design Min / Max clamping range: 0.0mm (0.0\\\") / 20.0mm (0.79\\\")
Recommended clamp torque: 1.5Nm
Back Can Options Blind Mount (BM): Complete with fixed back can
Pre Install (PI): Separate back can for pre installation
Cable Entry Options Cable clamp & squeeze connector for
conduit up to 22mm
Conduit Knockouts 3 Sets of horizontal positions: 19 / 22 / 28mm 0.75 / 0.87 / 1.10\\\"
Connectors Removable locking connector with screw terminals with \\\"loop through\\\" facility
Safety Agency Ratings (pending) UL-1480, UL-2043, CE
BM Hole Cutout Diameter 295mm (11.61\\\")
PI Hole Cutout Diameter 295mm (11.61\\\")
Dimensions
Bezel diameter: 325mm (12.80\\\")
BM model: Front of ceiling to rear of back can 310.50mm (12.22\\\")
BM model: Front of ceiling to top of safety loop 327.80mm (12.90\\\")
PI model: Front of ceiling surface to rear of speaker unit 118.70mm (4.67\\\")
PI model: Front of accessory back can bezel to top of safety loop 168.50mm (6.63\\\")
Net Weight (ea) CMS801 DC BM: 6.5kg (14.33lbs)
CMS801 DC PI: 2.5kg (5.51lbs)
CMS801 Plaster (Mud) Ring: 0.3685kg (0.81lbs)
CMS801 PI 8 Ohm back can: 4kg (8.81lbs)
CMS801 DC 60W transformer kit 8 Ohm : 1.095kg (2.41lbs)
Included Accessories C Ring
Tile bridge
Paint mask
Cutout template
Grille
Optional Accessories Plaster (mud) ring
S********************
va rugam sa va autentificati accesand urmatorul buton: